LUMINARE – version 2016
with remote control and prepared for DAC setup
AWARD – best headphone amplifier 2016 more then 1000,- USD
“The best is the enemy of the good … “
AUDEZE present here goods on the show CANJAM 2015 in Cosa Mesa with AudioValve`s LUMINARE …
of course you could also use at Audeze on the CANJAM another established headphone amplifier – but you didn’t,
you had consciously chosen to Luminare. Why Audeze had probably done it – everyone knows the answer …..
|The story of LUMINARE.
I do not really know why I have driven this project forward not many years ago. I think I was busy with a lot of other developments as well as trivial things like earning money for example. Perhaps mine is simply unaware that their headphones and amplifiers are experiencing a large hipe for years.
Anyway, the beginning of 2014 resulted in discussion with colleagues that I would have some products in my program that seemed almost ideally suited to put with the requirements of the headphone market apart.
No sooner said than done.
First, the IMPEDANCER befell a technical revision, it was expanding the range of applications for the RKV Mark 2 significantly, especially as a female teflon connector for headphones STAX was inter alternates. The bias voltage was obtained from the voltage signal, so no external power supply is in advance required. VERTO was born and VERTO laid the foundation for all further considerations in this topic, culminating now in the product with the name LUMINARE.
I can excuse at this point only for me actually that I started so fundamentally important development in the headphones sector so late (I slept through) and had thus deprived the public a potentially groundbreaking product. Many of you have their money invested now possibly poorly because there was nothing else on the market – that really am sorry.
But now back to Luminare.
It seemed to me as the basis for such a project, the OTL circuit of the RKV downright awesome. First, they had already claimed stable over decades in the market and on the other they had characteristics that should prove to be just the Luminare be extremely efficient and more full development. There would be for example the superior damping factor, low internal resistance, high bandwidth, and not least the low harmonic distortion he always particularly distinguished the RKV.
Now it was in principle “only” about output transformers so be interconnected in the OTL principle, which can be obtained if possible upright with transformer all these benefits. The advantage to couple a outpt transformer to an OTL circuit is that the repercussions and influences on the circuit itself ( either headphones or transformers ) are considerably lower. And this brings a projection on presence in the music, the listener will appreciate very quickly.
Everything else on this project was for me then just “routine”. A new circuit board develop, expand the circuit according to the light of all electro – physical principles and my over 45 years of experience in this topic.
And ladies and gentlemen, I am more than satisfied with my work, I hope you are there also – Helmut Becker
power consumption: 80 VA nominal – 120 VA full load
In summary, this means:
Note: Thus is L U M I N A R E the ONE AND ONLY headphone amplifier on the market that is able to drive all standard headphone loads, starting from 3 ohm up to 145.000 ohms.
deutsche Bedienungsanleitung [DE]
We ask anyone who would like to add something to the user manual of homemade experience with Luminare to a corresponding text note to Mr. Becker.
Rear side connector panel
Follow the forum posts for more information about Luminare !
OTWIN MAAS – Moderator OPEN-END-MUSIC, Germany
“Dies ist der beste Kopfhörer – Verstärker mit dem ich jemals zu tun hatte“
“Den Violectric V281 konnte ich mir im Vergleich mit dem Luminare anhören. Er ist ein gelungener KHV, der aus meiner Sicht klanglich über dem Vorgänger V200 steht, jedoch in der Gesamtbewertung nicht an einen Luminare heranreicht. Er hat nicht dessen Klarheit im Klang, stellt nicht dessen dreidimensionalen Raum hin und erreicht ihn auch nicht in Sachen Klangfarbe bzw. natürlicher Darstellung. Aus meiner Sicht bedient ein Luminare eine Klasse, die komplett über einem V281 liegt.” [ O. Maas)
The Violectric V281 I could listen to me compared with the Luminare. He is a successful amp, which is in my opinion sound than its predecessor V200, however, does not come up in the overall assessment of a Luminare. He does not have the clarity of the sound does not put out its three-dimensional space and also does not reach him in terms of tone and natural representation. In my view, a Luminare served a class that is completely a V281. [O. Maas)
Egal ob mit hoher oder mit niedriger Impedanz, mit hohem oder geringem Wirkungsgrad, egal ob dynamisch oder Magnetostat – keinen der angeschlossenen Kopfhörer habe ich bisher so erlebt, wie über den RKV 3, da öffnen sich tore zu neue welten.
No matter if high or low impedance, high or low efficiency, whether dynamic or magnetostat – none of the connected headphones I have ever experienced so how about the RKV 3, it will open doors to new worlds.
Aucune importance si le casque connecté présente une haute ou une basse impédance, une sensibilité élevée ou faible, qu’il soit électrodynamique ou isodynamique. Quel que soit le casque utilisé, je n’ai jamais connu un tel résultat que celui obtenu avec le RKV 3. Il ouvrira les portes sur de nouveaux mondes.
review by Dr. Martin Mertens, EAR – IN, 2/3 – 2015 ( RKV 2 + 3, basic concept for LUMINARE )
LOW IMPEDANCE mode: – test load 32 Ohm:
1 Khz – 0,1 watt – 0,06 %
bandwide: 15 – 100.000 Hz
OTL mode: test load 220 Ohm.
1 Khz – 0,1 watt – 0,015 %
bandwide: 12 – 150.000 Hz
max. load 2000 ohms
STAX mode: ( auto gain control )
bandwide: 15 – 150.000 Hz
|gain overview :
Mode: Low-Imp signal on the black headphone jacks + 16.5dB / and STAX connector 32dB + 6dB ( galvanic coupled sym. balanced complementary output STAX connector signal ) + 38 db
Description of some technical details …
The output impedance at Luminare with negative feedback (physical concept: closed loop) is defined as follows.
Example: The OTL mode provides Luminare 1V without load resistance and 0.998 V at 60 ohm load resistor.
|Explanation of the automatic gain circuit in Stax mode.
Luminaire has a elecronischen sensor that detects whether the Stax fashion a dyn. headphone is plugged or not. Using this electronic the user can choose whether he wants to increase the gain in the Stax mode or not. When the Stax fashion a dynamic headphone is plugged into the headphone jacks, the Verstärkungerhöung is overridden. This is only effective if the Stax fashion no dyn. Headphones equal time connected with the Stax headphones. A green LED on the front left on the board signals this condition, LED on means increased gain.
|This LED indicates when the bias voltage built up for the Stax headphones and stable.
|If you turn on the amplifier, reducing the volume and wait until this red LED goes off. As long as this red LED seems light up, all outputs of the amplifier is short-circuited and thus protect the headphones when the amp load or un – load the internal caps. This is always the case when the amplifier ON and OFF switches.
|The transformer was installed outside of the amplifier. This has the advantage on that the heat of the power transformer remains from the device and, second, that no stray magnetic fields cross the output transformer or the circuit board and modulate them. In addition, the transformer was covered with a layer of transformer sheet and thus absorbs stray magnetic fields. Then the transformer with a 2-component potting shed was in a metal cup.
( describtion coming soon …. )
Warranty and tube Note
On each board is the model name of the product and the name of the tubes is set. So if you are not sure which tube you need, please look at the circuit board and watch what is written there (PCL805 – or ECL85 (6F5P)
In mid-2015 has been changed from PCL805 on ECL85 that affects the models RKV all, Luminare and Solaris
The warranty is void if the top glass of the amplifier is taken within the warranty period. Also void the warranty, if other than that we offer tubes are used for the so-called “tube rolling”. To buy new tubes, please contact your dealer, he has recommended tubes on stock. Incidentally Tube Rolling is simply stupid in the models RKV, Luminare and Solaris. You can convince yourself by knocking on the tubes, they will not hear any knocking sounds in the headphones.
The picture below shows you the max. Output voltage before start soft clipping in OTL mode at 220 Ohm load per channel – at 43 Vrms are on each channel 8,3 watts