Warenkorb anzeigen „Challenger 250“ wurde deinem Warenkorb hinzugefügt.

Baldur 70

8.100,00

(English) But, damn, the Baldur 70 is one miracle of an amplifier. (Kenn Kessler)

Kategorie:

Beschreibung

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes

Während der CES Show in Las Vegas in 2003 wurde seitens der Besucher der Wunsch nach einer kleineren Ausgabe unserer BALDUR 200 plus geäußert. Größe und nicht zuletzt auch der Preis waren Anlass, sich den Kopf über eine kleinere Variante der BALDUR 200 plus zu zerbrechen, um so dem Konsumenten den alternativen Einstieg in die BALDUREN – Welt zu öffnen. 

Gesagt – getan, so finden Sie in der Wiedergabe der nebenstehenden Abbildung bereits den Referenz – Musteraufbau der abgeschlossenen Entwicklung einer sog. BALDUR 70 – (oder auch BABY – BALDUR)  – und wird erstmals auf der diesjährigen High End in Frankfurt in Zimmer 230 gemeinsam an den Lautsprechern der Fa. Lansche zu sehen und zu hören sein. 

Wie in all unseren größeren AUDIOVALVE Endstufen findet sich auch hier unser bewährter vollautomatischer Biasregulator – kurz ABR – an den Endröhren wieder. Dieser nach unserer Kenntnis weltweit einmalig und erprobte Regelmechanismus ist geradezu ein „Muss“ für regelrelevante Aufgaben zum stabilisieren des Bias – Ruhestromes der Endröhren und gehört zur Technik des 21.Jahrhunders einfach zum Standart – zumindest bei AUDIOVALVE.

Ein Sicherheits – und Betriebstandart, der für unsere Röhrenverstärker zum Synonym schon seit über einem Jahrzehnt ist. Aus diesem Grunde erhöht AUDIOVALVE auch in Kürze die Garantiezeiten seiner Produkte auf 5 Jahre.

Neben der hohen Zuverlässigkeit der Endstufe vereint  dieses Gerät selbstverständlich noch weitere interessante, typische AUDIOVALVE eigene Raffinessen seitens des Konzeptes. Als Endröhren kommen wie in der BALDUR 200 hier lediglich 4 Röhren, statt 8, des Typs 6AS7G, zum Einsatz. Wer je mit dieser Endröhre zu tun hatte kennt die Probleme um Ihre Handhabung und BALDUR 200 ist, die einzige weltweite Endstufe, die aus 8 Endröhren bis zu 150 W an 8 Ohm erzielt und das bei einer sprichwörtlich sagenhaften Dämpfung von 100 !!

Nun BALDUR 70 kann diese Werte nicht ganz erfüllen – soll sie auch nicht, vielmehr soll Sie all denjenigen, die sich schon immer für BALDUR 200 interessierten, einen preiswerteren Einstieg ermöglichen. Und der Preis für diese Teile ist Super – versprochen.

Aber was nun macht diese Endstufe zu etwas besonderem ? Es ist die  Summe aller konsequent angedachten und durchgeführten Entwicklungsschritte. Die Elektronik der BALDUR 70 ist auf einer einzigen riesigen Leiterplatte untergebracht – einem sprichwörtlichen Masterpiece besonderer Art – eben typisch AUDIOVALVE, mit dem Vorteil, das bei Aufnahme der Serienproduktion der Kunde immer einen Kopie unseres Referenzmusters erhält.

Sie müssen sich nicht mit den Problemen eines „Drahtverhaues“, oder der Tagesform des verdrahtenden Mitarbeiter als Qualitätsmerkmal des Produktes herumschlagen – wie es leider nur all zu oft noch immer der Fall ist.

BALDUR 70 hat eine derart ausgeklügelte komplexe und durchdachte Leiterplatte, das diese sich nicht verstecken muss – ganz im Gegenteil, sie wird zum zentralen Blickfang und ist geradezu ein Augenschmaus für den Betrachter und muss sich nicht unter Chrom – Chassis verbergen.

Aber das ist nicht der einzige Aspekt der für diese Leiterplatte spricht. Es ergeben sich im Rahmen der Konstruktion dynamische Wechselspiele zwischen den Leitungen und den Bauelementen, die sich in die Wiedergabe des Signals niederschlagen. Nur bei Verwendung einer gut durchdachten Leiterplatte ist sichergestellt, das auch der Stabilität dieser Verhältnisse Rechnung getragen wird. Bei Freiverdrahtungen ist kaum ein Verstärker wie der Andere – geschweige denn, wie das Referenzmuster, sondern gerät in die Abhängigkeit der Sorgfalt des jeweils am Gerät arbeitenden Mitarbeiters.

Bei der Verwendung der Endröhre 6AS7 G, die erstmals 1982 von uns in der BALDUR 100 Anwendung fand, ( als Initialzündung für weitere weltweite Entwicklungsansätze ) gibt es eine Reihe von Sorgfaltspflichten zu erfüllen um der Röhre ihre gesamte Musikalität ihrer Lebensdauererwartung zu entziehen und darüber hinaus stabile Verhältnisse zu schaffen. Immer wieder wird jedoch auf solche – maßgeblich zur Sicherheit beitragende – Maßnahmen verzichtet, die einem dann schnell die Freude an der Verwendung dieser Röhre rauben. Die hohen Fertigungstoleranzen der 6AS7 lassen sich nur mit unserem autom. Biasregler ABR wirklich wirksam reduzieren und somit alle Röhren in Gleichtakt bringen – auch die konventionelle Justage der Biasströme mit Schraubenzieher kann diese Ausgewogenheit der Gleichtakt – Balance nur für kurze Momente gegeben – wenn überhaupt.

Selbst selektierte Röhren können hier auf Dauer ihr Versprechen nicht halten, laufen aus dem Arbeitsbereich – verlangen nach Austausch oder Justage und belasten letztlich nur Ihre Nerven und  Ihren Geldbeutel. Nicht so in der BALDUR 70 – sie besitzt für jedes der beiden Triodensysteme eines Glaskolbens einen eigenen vollautomatischen Biasregulator (ABR). Allesamt sind die 6AS7 noch zudem über reversible Sicherungen geschützt sind. Wann immer Sie also diese Röhre im Einsatz sehen, fragen Sie nach der techn. -Gestaltung des Umfeldes der Endröhre – und sollten Sie lediglich ein halbes Dutzend Bauelemente um die Röhre placiert finden, wäre gebotene Skepsis Ihr bester Berater.

Und sollten Sie einmal selbst eine Endröhre in der BALDUR 70 wechseln müssen, signalisiert Ihnen der jeweilige ABR Schaltkreis die Notwendigkeit uns Sie tauschen sie gegen eine Neue aus – auch im eingeschalteten Zustand. BALDUR 70 ist mehr oder weniger „unkapputbar“ auch wenn Sie die Endstufe kurzschließen oder aber versehentlich ohne Last Laufen lassen. Das gilt übrigens für all unsere Endstufen.

BALDUR 70 erreicht mit Dämpfung 20 zwar nicht den Traumwert Ihres großen Bruders, spielt aber dennoch im Vergleich mit dem Wettbewerb absolute in der Oberliga, da Dämpfung nun nicht gerade eine Stärke von allgem. Röhrenendstufen ist – man denke da an einige OTL – Konzepte, die mit Dämpfung 2 Ihnen Glauben machen wollen, dies musiziere vortrefflich – in Sonderfällen vielleicht, aber nicht im allgemeinen. Es funktioniert eben einfach nicht ohne Kontrolle des Lautsprechers.

Für die in BALDUR 70 realisierte Dämpfung bedeutet dies musikalisch betrachtet, kraftvolle saubere, trockene und scharf konturierte Bässe – kein „Schlabberbass“ also, begleitet von der Soundstage, wie man sie nur von Trioden kennt

BALDUR 70 ist kein Verstärker, der lediglich an einem, auf die Anlage abgestimmten Lautsprecher musiziert, BALDUR 70 treibt neben dyn.- Lautsprechern auch durch seine hohe Linearität ausgezeichnet Magnetostaten und ist damit universell an einer Vielzahl gängiger Lautsprechern ausgezeichnet zu betreiben.

Natürlich hat BALDUR 70 auch einen Treiberteil. Er besteht aus vier Doppeltrioden, die der Signalverstärkung und der Bildung des Komplementärzweiges zur symmetrischen Ansteuerung in einer parallel – spiegelsymetrischen Anordnung der Endröhren dienen. Heizspannnung sowie Anodenspannung des Treibers sind selbstredend gleichfalls aufwendig stabilisiert und sorgen für grundweg solide und stabile Betriebsverhältnisse. Die übrigen Ausstattungsmerkmale der BALDUR 70 ähneln ansonsten denen der BALDUR 200 plus.

 one reason for the excellent musical playback quality of the audioValve amplifiers is the fact that the output transformer is based on near perfect transmission characteristics. Audiovalve power amplifiers reproduce rectangles at 10 khz, which otherwise are only known from the theoretical ideal treatise on textbooks. Anyone attentively studying the American audio press has probably already found many of these images that are not nearly close to the theoretical ideal – just as audiovalve amplifiers do, so the success of the musical reproduction of audiovalve amplifiers is unstoppable and will prevail, everything only a matter of time.

 

 

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter

Specs

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes
techn. - Angaben: 
  • Netzspannung: 100 - 245 V
  • Leistungsaufnahme. 250 Watt
  • Bestückung: 4* 6AS7G, 1*ECC83, 2*6189, 1*6N6P
  • Prinzip: PP Technik - Class A
  • max. Ausgangsleistung: an 8 Ohm - 70 Watt
  • durchschnittlicher Klirr: 100 Hz - 1 KHz - 10 KHz, 0,3 %
  • Leistungsbandbreite: 10 Hz - 50Khz, Last 8 Ohm
  • Innenwiderstand: 0,4 Ohm
  • Dämpfungsfaktor: 20
  • Eingangsempfindlichkeit: 0 dBm
  • vollautomatische Bias- Servo - Regler an allen 8 End-Trioden
  • kreuzgekoppelter parallelsymetrischer Treiber
  • div. elektronische Sicherungen bei Röhrendefekt
techn. Änderungen vorbehalten (Stand - April 2018)
Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter

Awards

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes

(English)

and the winner is …….  HEATHROW – SHOW , London 2004 – AudioValve win the international title  „INDUSTRY AWARD 2004 in the categorie

„best tube amplifier“

 

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter

Hifi magazines

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes

(English)

Wherever and however the ‚radar‘ is focussed, too many worthy brands suffer in near-anonymity below its sweep. Some deserve to, some don’t. Germany’s AudioValve is one of the latter. Aside from questionable aesthetics, their products are hard to fault for performance, build quality, reliability or – most remarkably – value for money despite being made entirely on the Continent; there are no off-shore cost benefits here. So far, I’ve reviewed a couple of their more affordable integrated products and their under-priced Eklipse pre-amp, and loved each one of ‚em. Now (he said, rubbing his hands in anticipation), it’s time to play with the big stuff.

No, not the rather scary Baldur 200+, but what a few observers have already deemed to be amongst the best-value, all-tube, high-end monoblocks on the market today. According to AudioValve’s charming Frau Heike Becker, who handles sales, customer relations and technical queries (sexist pigs, take note: she’s an electronics engineer), ‚During the 2003 CES show in Las Vegas, it was obvious that there was a need for a smaller version of the Baldur 200+. Everyone loved it, but it was too much for some. According to the dealers and distributors, size and price were the main reasons we needed to develop an alternative, entry-level Baldur.‘ So her husband Helmut, the designer of all of the AudioValve products, set to work.

Only a few months later, at the ‚High-End-Show‘ in Frankfurt, they unveiled the Baldur 70 Class-A triode monoblock, which was immediately dubbed the Baby Baldur. It even looks like a 3/4 scale model of the original Baldur. And like every other one of AudioValve’s larger power amps, it features the novel circuitry that Helmut has perfected over a decade. As Heike (whose English is fluent, while Helmut’s is about as good as my German) explained, ‚AudioValve has absolutely no interest in the „exotic valve game“ that forces customers to spend a fortune of so-called, „selected“ valves. Helmut designed a circuit that takes automatic biasing to another level, eliminating concerns for minor variations from valve-to-valve. The circuit even allows the user to mix tube types within the same channel, like 6550s and KT88s.‘

Called the ‚automatic bias regulator‘, or ABR for short, it endows the amplifier with a number of benefits, including instant warning if a tube has ‚gone bad‘ while ensuring that nothing nasty reaches the outputs. The circuit matches the tubes, continually adjusts the bias and acts like an on-board, real-time tube tester. Because the comprehensive capabilities of the ABR circuit obviates the need for over-priced, matched valves, it’s reflected in the price. Frau Becker notes that, ‚Some companies charge up to 100 euros each for the valves we use. We charge less than that to replace the output valves for the whole amplifier.‘ And as one observer noted, there are amplifiers out there that cost more to re-valve than you’d pay for a pair of Baby Baldurs.

Along with an extremely reliable output stage, the ‚Baby Baldur‘ includes other familiar details (to Baldur owners, that is), such as balanced or single-ended operation and the cluster of red LEDs that indicates when the unit is in stand-by or if a valve needs replacing. The valves line-up, per amplifier, consists of a quartet of 6AS7G power triodes while the Baldur 200+ uses eight per side. The input and driver complement includes one ECC83, one ECC82 and two 6N6Ps – none of which will break the bank at re-valving time. With half the output tubes, the Baby Baldur delivers half the power of the Big Baldur, circa 75-80W…though it seems like a lot more.

As is favoured by Helmut Becker, all of the electronics of the Baldur 70 are on one enormous printed circuit board, viewed through the clear Perspex top-plate. The valves peek through it and are protected by a cage. [Note that the curved rods that form the cage on the review sample have been replaced in certain markets – including Europe – with a new cage that won’t permit fingers to poke through the gaps.] Helmut prefers well-made, well-filled, top-grade circuit boards to hard-wiring because, ‚The advantage is that all the production models of whichever AudioValve model you try are exactly like the reference sample, in contrast to „hardwired“ components, where the outcome varies with the soldering abilities of the constructing technician. All too often, unfortunately, the case with hard-wiring is that one amplifier is hardly like the other. At AudioValve, we compare every amplifier we produce to the reference sample.‘

Helmut adds, however, that sample-to-sample consistency is certainly not the only reason for using a single PCB. ‚Dynamic inter-relations can occur between the various components, in the context of the total construction. Only the use of a well thought-out and carefully-calculated printed circuit board will stabilise or eliminate these conditions.‘

Helmut found with the power triode 6AS7G, which he first tried in 1982 in the original Baldur 100, that there are a number of demands that must be met before this valve will perform to its maximum ability. ‚For one, there has to be a stable electrical environment to sustain this highly-demanding tube if you expect to achieve maximum musicality during its entire lifetime. The intricacies and traps with the 6AS7G are such that they cannot perform this task without an automated bias circuit and simply cannot be done without AudioValve’s ABR. ABR forces all the tubes effectively to act in a „common mode“, fundamental for any multiple tube design.

‚Traditionally, this task is performed with a screwdriver, to adjust the bias current, but that is only a momentary fix, if at all. Even selected tubes cannot deliver their potential in the long term, because tubes age and change, and a matched pair or quad grouping will be „matched“ only for so long. ABR regulates each of the two triodes in one glass bulb and so on with the other tubes. Whenever you see this tube in use, accompanied by only a half-dozen components around it, scepticism will be your best response.‘

If you need to change an output valve in the Baldur 70, the related ABR circuit will indicate its terminal status or pending demise via the aforementioned LED, and you have to change only that valve for another, either new or even used. You just plug it in and off you go. The ABR circuit will compensate for, say, ageing in a valve you found in your ’spares‘ box. Helmut argues, too, that the Baldur 70 is more or less indestructible, even if you short circuit the output, or inadvertently, leave it running without a load. He adds, ‚That, by the way, applies to all of our amplifiers!‘

Given the power rating and the option of balanced operation, the Baby Baldurs were drop-in replacements in my main system: SME 30 Mk II turntable with Series V arm and Decca Reference cartridge, EAR 324 phono stage, Marantz CD-12/DA-12 CD player. McIntosh C2200 preamp and Wilson WATT Puppy 7, all wired with Transparent Reference. Thus, the main comparison was with the amplifier for which I substituted the AudioValves: the McIntosh MC2102. More powerful, more expensive and easily as advanced – maybe it was unfair to the AudioValve, but the results proved otherwise. I also wired in the Nu-Vista 300s and the McIntosh 275 reissue, and had other amps like the PrimaLuna Prologue One in use during the same period.

As luck would have it, the amplifiers were completely burned in, the pair having made the rounds of the UK for nine months. Yes, this review is running almost a year late, but far be it for me to berate distributors; let the retailers and suppliers beat ‚em up. Suffice it to say, I’d almost forgotten I was supposed to review it. Anyway, it was worth the wait, because – instantaneously – the Baby Baldurs delivered performance so far beyond what I had expected that I found myself undergoing the exact same shock revelation I experienced a few months ago with the ProLogue One, but at a higher price point.

Installation was a breeze as the inputs and speaker terminals (sets for 4 and 8 ohms) are widely-spaced and of top quality. Switch on is but a brief ritual: First, you flick the main power rocker, followed a few seconds later by the stand-by switch. The LEDs extinguish when the amplifier is ready to use. After five minutes or so, the units were warmed-up to optimal running temperature, but some valve fusspots may prefer a half-hour.

Regular readers know that, although they’re sensitive, WATT Puppies are not an easy load, and they are so revealing that they can easily embarrass most amplifiers. At the risk of alienating 75 percent (or more) of you, they also show in spades why solid-state amplifiers are NOT the preferred mode of amplification for some of us. So, while the Baby Baldurs are hardly the sort of behemoths most WATT Puppy owners will use, they are, at least, sonically sympathetic to the Wilson speakers, and the immediately-perceived synergy was flagged by a deliriously sweet top end simply unavailable from the WATT Puppies when driven by transistor amps. (Let me qualify that with an ‚In my experience…‘.)

Confirming this initial response were smiles all around with every listener who visited during the review period. But however much I expected them to comment on the glistening, silky treble region, the most oft-elicited response was a real shocker, especially when you consider we’re talking about a valve amplifier with output only in double figures. To a man, each and every visitor commented first on the sublime bass: controlled, deep and, above all, natural.

Let’s examine this a bit more closely. Despite the compact dimensions of my room – 12x18feet – it acts almost like a quarter-scale version of the SME room because of its solidity. As such, within its confines, it is able to deliver smooth, controlled and rattle-free bass. [Interestingly, when the gents from PMC arrived and we ran a test sweep, the only crud we found at low frequencies turned out to be buzzing caused by some loose CD jewel boxes sitting near the speakers.] It managed to exploit the sheer power of the Puppy bass module with the efficacy of a big solid-state amplifier, but without applying most tranny amps‘ unnatural overdamping.

Even with a bottom octave foundation that substantial and solid, and upper frequencies as honeyed as those from a Dynaco Stereo 70 or Radford STA-15, the best was still to come. Hands down, this pair of monoblocks creates a soundstage as wide, deep, open and airy as any I’ve experienced from amplifiers under £5000. It is thoroughbred soundstage recreation as beloved of American audiophiles with massive panel speakers and a cherished Denon 103D. I whacked up the volume for the stereo mix of the Beach Boys‘ ‚Surfin‘ USA‘ off the newly-released Best of and marvelled at the smooth lateral spread, from a recording that can sound ping-pongy at worst. The cheesy organ break, Brian’s chunyk bass playing and uncluttered, but perfectly blended harmonies – Charlie may not surf, but Fritz clearly does.

When it came to the new Wilson Phillips CD, definitely the ’sleeper‘ of the year because of pop snobbery, the Baldur 70s showed how they could handle a trio of ultra-sweet voices backed by the slickest of studio sessioneers: clarity, detail and a way with layering that will baffle those who simply refuse to believe in front-to-back depth, especially listeners still stuck in a 1980s UK solid-state rut.

But it was something entirely unexpected, unwarranted and unreasonable that made me fall head-over-heels in love with the Baby Baldurs: 1950s mono recordings of the Capitol variety. Sick puppy that I am, I fed the Baldurs track after track of Mickey Katz – vinyl and CD – to hear my fave Yiddish klezmer comic, with Benny Goodman-grade clarinet, vocals recorded with the finesse of the best Frank/Dino/Nat classics, percussion just waiting to be sampled by the hip-hop thieves. Through the Baldurs, the sound was palpable and room-filling – kosher, even. Within seconds, listeners forgot that they were listening to a single-channel recording, the sound plunked straight in the middle of the speakers, in the room. Why the recidivism? Because it was so fat, rich and, above all, lifelike that satisfaction was guaranteed. The readily-available layering of a stereo recording was evident here with unmistakeable lucidity. You could taste the soured cream and blintzes. Expect Mickey Katz LPs to shoot up on eBay.

Consistent from source to source, recording to recording, was an effortlessness that belied the power rating, though a headbanger could reach its limits if the speakers were too hungry. And the amplifiers are, despite Frau Becker’s insistence, sensitive to clean mains, if insensitive to cable selection. Overall, though, they behaved impeccably, and I wouldn’t imagine that any owners would fail to pay attention to positioning, ventilation or, indeed, choice of AC cables.

And in the back of your mind, all the while you savour the sound, there lurks a crucial specification that should make the Baby Baldur the hit of the season: a pair will set you back around £3195 depending on finish.

Let’s put this into context. Here’s Kessler, with no great love for the Fatherland, raving feverishly about another Teutonic tube amp, and in under a year. While it is completely unlike the T+A, which is ultra-modern and ‚lifestyle‘ and sexy, it represents the same sort of value – real and perceived. It will not replace the McIntosh, which edges it out in absolute dynamic contrasts, absolute quietness and sheer grunt, as well as looks. And I still have dreams of the Marantz Project T-1, the Nagras and one or two others requiring a lottery win. But, damn, the Baldur 70 is one miracle of an amplifier. ‚Today Kessler, tomorrow….‘

These are a physically imposing pair of amplifiers. Weighing in at 79 pounds and occupying a 17.25″ square x 14″ high piece of the room … EACH!

 

The result of all this weight and size is an amplifier which is sweet and delicate sounding when called for, yet authoritative and in control when needed. The tubes used are the very musical 6AS7 output tubes, which are biased automatically by the amplifiers proprietary internal circuitry. The result is an excellent balance across the gamut of musical styles and tastes. I played everything from delicate original instrument chamber music and soft vocal solos to loud, rowdy rock and large orchestral pieces … all at various volume levels. The Baldur sailed through it all with equal aplomb. Two common knocks against vacuum tube amplifiers in general is that they are too fussy or that they don’t provide the bass power and control of their solid state brethren. Well, the Baldur is only one of many examples in the tube world which makes either of those statements meaningless and untrue. Sure, there are some tube (valve) amps which require a bit of fussing or which don’t have very good bass … sometimes both shortcomings … but not this one and certainly not all of the others either!

 

The Baldur had a musical footprint which was obvious yet paradoxically „uncolored“ in terms of it’s sonic qualities. There was no distinct impression that this is a valve amplifier garnered during listening tests. It’s bass is tight and well controlled without being over-damped and „dry“ sounding. („damping“ is the electronic means by which an amplifier controls extraneous woofer motion; commonly referred to as „damping factor“) Track after track left the impression of a well focused yet large and deep soundstage. Ambient retrieval is very good, indicating a low noise floor. {This is an area where all the solid state amplifiers have an advantage over all the tube amps in this roundup … they are inherently less noisy when there is no music is being played.} The noise floor becomes a factor in retrieval of ambience and overall detail. The Baldur did give a very good sense of ambience when called upon and the images it portrayed were quite holographic and correctly proportional to each other. High frequencies are rendered without a hint of glare or overdone presence. Cymbals, bells, triangles and the harmonic tones of a children’s choir are very well served by the Baldur. Another area which can be well noticed between differing power amplifiers is the sensation of correct (musical) pace and „timing“. The Baldur, along with most others in the roundup, is a real champ in this respect, always leaving the listener with the feeling that the reproduction is spot-on. The transparency of any amplifiers ability to peer into the soundstage is something which can not be measured, but which is immediately apparent to anyone who has done an A/B with two amps having vastly differing capabilities in this respect. The Baldur is a very transparent amplifier, peering clearly into the soundstage and allowing us to sense the spacing between individual instruments and vocalists quite clearly.

 

Although the soundstage wasn’t quite as large as the Parasound JC-1 and Krell FPB 450Mcx, as transparent as the Electrocompaniet AW-400, as well defined as the Simaudio W-10 and Sunfire Signature or as rich in the „gravitas“ area as the Rogue Zeus and the Marsh A-450, it was a terrific blending of all the above, and well worth anyone’s consideration.

 

Audio Valve: Challenger 150;    { $8,859; 140-180 wpc (depends on output tube type) }

 

The Challenger 150 is in the middle of Audio Valve’s other line of amplifiers. Unlike the Baldur line, it is not a class-A amplifier. It can however, utilize differing output tubes, allowing the owner to pick the tube which suits their musical preferences the best. The tube used during this roundup is the EL-34 tube, which is highly regarded for it’s fluidity and smooth midrange … albeit at some loss in power compared to a 6550C or a KT-88. (to name just two) The build quality is exactly what I’ve come to expect from Audio Valve … excellent, with no criticisms whatsoever.

 

Sonically, the Challenger was challenged by it’s rivals in the test and most clearly by it’s brother. The soundstaging is excellent and well-defined. Transparence was very good yet compared to the best of the best, it was slightly less focused then some, and didn’t have the bass power and control which I experienced with the Baldur. Please bear in mind the differences are minimal and the cost differentials are large.[ although in my mind, worth it ] This is a very good amplifier. I feel that if it had come with 6550C output tubes I would have liked it even more. I am looking forward to hearing the amp again at more shows. The Audio Valve „house sound“ is very appealing to me since it is more focused on the music instead of the hi-fi equipment. (PS: Their pre-amp is a knockout too!)

 

 

Joe Shanaphy

Audio/Video Editor, That’s Life! magazine

(201) 785-1055

[cell] (201) 669-8700

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes

user manual

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter

FAQ

Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter
4.3 (86.67%) 3 votes
Share this...
Share on Facebook
Facebook
Tweet about this on Twitter
Twitter

Bewertungen

Es gibt noch keine Bewertungen.

Schreibe die erste Bewertung für „Baldur 70“

Deine E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert.



Exclusive products

Special category of products

Durch die weitere Nutzung der Seite stimmst du der Verwendung von Cookies zu. We use cookies to improve your experience using our website. Weitere Informationen

Die Cookie-Einstellungen auf dieser Website sind auf "Cookies zulassen" eingestellt, um das beste Surferlebnis zu ermöglichen. Wenn du diese Website ohne Änderung der Cookie-Einstellungen verwendest oder auf "Akzeptieren" klickst, erklärst du sich damit einverstanden.

Schließen